Components and Subsystems

4701 - 4705 Series Low Profile Power Transformer

LOW PROFILE Transformer for printed circuit mounting. Five sizes: 2, 6, 12, 24 and 48 VA ratings.

Features: 
  • Split bobbins for increased dielectric strength and low capacitive coupling
  • 115/230 volts, 47/63 Hz primary windings
  • CSA listed (LR 47366) and U.L. recognized (E100878)

TPW-4671 Series Input/Output Transformer

The TPW-4671 transformer is designed to interface with the subscribers premises (NT) and the 2- wire line side of the Central Office Equipment (LT) in the ISDN Network.

Features: 
  • Meets the electrical specifications of ANSI TI.601-1988
  • Approved for the Mitel MT8910 DSLIC strong device.

TPW-4670 Series Input/Output Transformer

The TPW-4670 transformer is designed to interface with the subscribers premises (NT) and the 2- wire line side of the Central Office Equipment (LT) in the ISDN Network.

Features: 
  • Meets the electrical specifications of ANSI TI.601- 1988
  • Approved for the Siemens PEB2091 device.
  • TPW-4670-1 meets the requirements of the Thomson SD5411 device.

CTS-4669 Series Common Mode Inductor

CTS-4669 is a 4-winding common mode choke, specifically designed to suppress EMI on the 4-wire S-Bus in the ISDN system.

Features: 
  • Windings are extremely well balanced
  • Maintains High Longitudinal Balance required in the system
  • CCITT recommendation I.430

TEW-4610 Series Input/Output Transformer

The 4 wire interface between Subscriber Terminals and The Network Temination has been standardised by CCITT recommendation I.430. The TEW4610 has been approved for use with the INTEL S-bus interface device S29C53.

Features: 
  • Uses a passive bus
  • Provides separate receive and transmit loops
  • Operating at 192 Kbits/s

TEW-4596 Series Input/Output Transformer

TEW-4596 is designed to be used either as a transmit or a receive transformer in the ISDN primary rate access network for T1 and CEPT applications.TEW-4596 is recommended for use with the following  devices: Crystal; CS61534, CS61535, CS61574 CS6158. Level One; LXT300 LXT301 LXT305.

Features: 
  • Primary rate ISDN network nodes
  • PBX or computer to T1/CEPT Digital trunks
  • High speed data link using T1/CEPT Digital Trunk

CTP-4563 Series Medium Current Toroidal Inductor

CTP-4563 is a medium current inductor with Core type: 1.57” o.d., Moly-Permalloy Powder, perm 125. Power rating: 4.50 watts for temp. rise 50°C. Typical applications: Switching Inductors in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads (2.00”)

CTP-4562 Series Medium Current Toroidal Inductor

CTP-4562 is a medium current inductor with Core type: 1.30” o.d., Moly-Permalloy Powder, perm 125. Power rating: 3.13 watts for temp. rise 50°C. Typical applications: Switching Inductors in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads (2.00”)

CTP-4561 Series Medium Current Toroidal Inductor

CTP-4561 is a medium current inductor with Core type: 1.06” o.d., Moly-Permalloy Powder, perm 125.Power rating: 2.16 watts for temp. rise 50°C. Typical applications: Switching Inductors in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • 4-pin header, for vertical mounting
  • Threaded center hole, flying leads (2.00”)
  • 2-pin header, for vertical mounting

CTP-4560 Series Medium Current Toroidal Inductor

CTP-4560 is a medium current inductor with Core type: 0.80” o.d., Moly-Permalloy Powder, perm 125. Power rating: 1.2 watts for temp. rise 50°C. Typical applications: Switching Inductors in Switch Mode Power Supplies.

Features: 
  • Flying leads (1.00”), for vertical or horizontal mounting
  • Threaded center hole, flying leads (2.00”)
  • 2-pin header, for vertical mounting
Syndicate content

Recent Events

June 10, 2018 (All day) - June 15, 2018 (All day)
City:
Philadelphia
,
Province:
Pennsylvania
Country:
United States
The IEEE MTT International Microwave Symposium (IMS) is the premier annual international meeting for technologists involved in all aspects of microwave theory and practice. It consists of a full week of events, including technical paper presentations, workshops, and tutorials, as well as numerous social events and networking opportunities. The symposium also hosts a large commercial exhibition. Co-located with IMS are the IEEE RFIC and ARFTG conferences.
May 30, 2018 (All day) - May 31, 2018 (All day)
Street:
4899 Uplands Drive
City:
Ottawa
,
Province:
Ontario
Country:
Canada
Join the Emcon team at CANSEC 2018 as they showcase the latest developments in TEMPEST, rugged, and high security IT solutions for the government marketplace. CANSEC is Canada’s annual Defence exhibition taking place at the EY Centre in Ottawa. CANSEC is Canada's foremost defence technology showcase. A two-day event, CANSEC will feature 120,000 square feet of indoor exhibits by Canada's leading edge defence and security companies, as well as an outdoor static display. This showcase targets a wide audience of customers that includes Government agencies and departments with an interest in the defence sector.